Kubota ARN323 (6944)

[Capital information]
▼ Body
Manufacturer: Kubota
Model: ARN323
Number of harvestors: 3 (Katsu)
Horce: 23 (PS)
Hour: 486 (H)
※ As there are movements in the warehouse, etc., please acknowledge some errors.

Crawler width: 400 (mm)

▼ Status / Storage Location
Status: Steady state:
Management base: Miyagi Prefecture Kurihara City 1st yard
Management number: 2102

[Equipment without]
Cabin: None
Canopy (hood): None
Notta: Yes
Auxiliary Devida (OK, Swiss, etc.) None
Automatic horizontal control (left and right): Yes
Automatic horizontal control (front and rear): None

[Please confirm the following]
○ Engine start-up
○ Operation confirmation ※ Continuous use in actual work is not performed.
○ There is no accessories
○ We are careful about inspection etc., but it will be handed over at the present situation. Please consider the following and look at the result of inspection.

[Exterior part inspection]
Type nameplate seal damaged almost no
Model seal (left, right) Corruption almost no
Sheet damage
Devider tip-breaking almost no
Devider Side Cover Corrupt
Tank club breakage
Threshing Cover Device Deviationless
Cutter cover (rear) not installed
Side mirror (left / right) No damage
Non-cabin roof

【Example of inspection】 ※ Only confirmation item only

Engine oil [2. dirt]
Air Cleaner Element [9. Dirty]
Winker (after) [98 flashing (right)]
Winker (after) [99 flashing (left)]

【Remarks】
Crawler (left and right) with small cock

[Results] All items
The following is the entire item of inspection results of this machine.
Engine oil [1.%] or higher
Engine oil [2. dirt]
Radiator [3. Amount] Normal
Radiator [4. Color] normal
Radiator [5. Water leak]
Reserve Tank [6. Damage / Stockless] None
Fanbert [7. Stockless] None
Air Conditioner Belt [8. Stock] Non-loaded
Air Cleaner Element [9. Dirty]
Air Cleaner Element [10 Damage / Stockless] None
Engine start [11 operation]
Battery [12 operation] Almost normal
Exhaust [13 smoke] normal
Mowring up [14 rising / falling]
Advanced / reverse (driving) [15 operation]
Advance and reverse (work) [16 operation]
Advanced and reverse (falling) [17 operation] not installed
Normally pivot [18 operation (right)]
Normal turn [19 operation (left)]
Brake pivot [20 operation (right)]
Brake pivot [21 operation (left)]
Spin turn [22 operation (right)] not installed
Spin turn [23 operation (left)] not installed
Cive turning [24 operation (right)] non-loaded
Deurization [25 operation (left)] not installed
Drive sprocket [26 oil leak (right)]
Drive sprocket [27 oil leak (left)] no
Crawler [28 large cracks (right) (looking from outside)] almost no
Crawler [29 big cracks (left) (from outside)] almost no
Brox (upper) [30 fixing (right)]
Brox (upper) [31 sticking (left)] non-loaded
Ring (bottom) [32 fixing (right)]
Ring (bottom) [33 sticking (left)] None
Movable roller [34 fixing (right)]
Movable roller [35 fixing (left)]
None None [36 shortages / defect]
No blade [37 shortages, defect]
こ 回 回 回 3 動 作 る
Feed chain [39 operation]
Toumi [40 operation]
Swing flow board [41 operation]
Waraka Chain [42 Operation]
Waratain (nail) [43 shortages and defect]
Waratain (nail) [44 operation]
Cutter blade (cutting) [45 shortages / defect]
Cutter blade (feed) [46 shortages / deficiency]
Cutter Blade (Cutting) [47 Operation]
Cutter blade (feed) [48 operation]
No. 49 [49]
2nd Lacen (horizontal) [50 operation]
No. 1 Lacen (Vertical) [51 Operation]
2nd Lacen (vertical) [52 operation]
Oruger Release Operation (Manual) [53 Lift]
Oruger Runction (Manual) [54 Right Turning]
Auger Release Operation (Manual) [55 Left Pivot]
Oruger teeth operation (manual) [56 down]
Authority operation (automatic) [57 automatic swivel (right)]
Authorion operation (automatic) [58 automatic swivel (left)] not installed
Oruger Runction (Automatic) [59 Automatic Swirl (After)]
Orhalonation operation (automatic) [60 automatic storage]
Auger OP (zoom swing shutter etc.) [61 operation] not installed
Emission racemic operation [62 operation]
None
Mowet [64 operation]
Caused nails [65 shortages / deficit]
Cause nails [66]
Auxiliary Device Nail [67 Stock Loss] Not Mounted
Auxiliary Device Nail [68 Operation] Non-loaded
Belt with protrusion [69 missing / deficit]
Belt with protrusion [70 operation]
Star Wheel [71 missing / deficit]
Star Wheel [72]
Corporate Corporation [73 Operation]
Kakikomi (nail) [74 shortages / deficit] Non-loaded
Kakikami (nail) [75 operation] not installed
Header transfer (nail) [76 shortages / deficiency]
Header transfer (nail) [77 operation]
Big depth chain [78 operation]
Koi depth (manual) [79 operation]
こ (automatic) [80 lamp lighting]
When cutting and shift switching (standard) [81 operation]
When cutting and shift switching (high speed) [82 operation] not installed
When cutting and shift switching (low speed) [83 operation]
Left and right horizontal control (manual) [84 operation]
Left and right horizontal control (automatic) [85 operation]
Before and forth horizontal control (manual) [86 operation] not installed
Horizontal control (automatic) [87 lamp lighting] not installed
Sorting Automatic Lamp [88 Lights] Non-loaded
Auto Clutch Lamp [89 Lights]
Automatic lubricating switch [90 reaction] not mounted
Emergency stop switch [91 operation]
Radio [92 operation] not installed
Panel operation (confirmation of rotation only) [93 operation]
Light [94 lighting (right)]
Light [95 lit (left)] not installed
Winker (previous) [96 flashing (right)]
Winker (previous) [97 flashing (left)]
Winker (after) [98 flashing (right)]
Winker (after) [99 flashing (left)]
Horn [100 sounds]
Air conditioner [101 cooling] not installed
Air conditioner [102 air volume change] not installed
Work, etc. [103 lit]

【Precautions】
· We do not check other than inspection items, please check with photos etc.
· Belt-related wear condition is not checked.
· Wear of Racen is not checked.
· We do not check chain and consumables.
· We do not check wear of the rolling rolling roll.
· The crawler check is simple, but it is not checked to the detailed part.
· Horizontal automatic checks the lighting of the lamp, etc., but it is not checked until operation.
· Automatic depth Automatic automatically checks the lighting of the lamp, but it does not check until operation.